Question about Automation Clips

Discuss how to use FL Studio

Return to “FL Studio Users Forum (Looptalk)”

Forum rules
Please read them here.
[You can only see part of this thread as you are not logged in to the forums]
Organonfire
Wed Aug 10, 2022 4:11 am

x

Question about Automation Clips

Hey everybody!!

So, I was creating some GrossBeat presets when I found that at the end of the GrossBeat fx, even though I set an Automation Clip in the GrossBeat's Mix Level, I'm still getting an unwanted extra sound fx. After further investigation I realized that even tho I did a hard cutoff in the Automation Clip, the Mix Level knob is very slow to go from 100% to 0%

Didn't a hard cutoff used to go from 100 to 0, or vice versa, instantly? Why is it so slow?

Just to make sure I did an Automation Clip for it's Mute/Solo and it was instantaneous.

It's been a long day so I'm probably not explaining this correctly, so I attached a photo. Not of the slow Mix Level knob but just the automation clips instead.

thanks if anybody could help me figure this one out.
You do not have the required permissions to view the files attached to this post.

levendis
Wed Aug 10, 2022 7:15 am

x

Re: Question about Automation Clips

Have you got Smoothing engaged, in the Remote C...
You do not have the required permissions to view the files attached to this post.

nucleon
Wed Aug 10, 2022 8:41 am

x

Re: Question about Automation Clips

Organonfire wrote: ↑Wed Aug 10, 2022 4:11 am He...

Organonfire
Wed Aug 10, 2022 2:55 pm

x

Re: Question about Automation Clips

levendis wrote: ↑Wed Aug 10, 2022 7:15 am Have ...
You do not have the required permissions to view the files attached to this post.

Organonfire
Wed Aug 10, 2022 2:58 pm

x

Re: Question about Automation Clips

nucleon wrote: ↑Wed Aug 10, 2022 8:41 am Organo...
You do not have the required permissions to view the files attached to this post.

abelg
Wed Aug 10, 2022 3:11 pm

x

Re: Question about Automation Clips

Maybe Nucleon is referring to the Time and Volu...
You do not have the required permissions to view the files attached to this post.

levendis
Wed Aug 10, 2022 3:12 pm

x

Re: Question about Automation Clips

Automation links are tweakable in the Remote Co...

Sancho Slikk
Wed Aug 10, 2022 3:23 pm

x

Re: Question about Automation Clips

Dear Automoto Masters, How Does it work? How d...

nucleon
Wed Aug 10, 2022 3:25 pm

x

Re: Question about Automation Clips

abelg wrote: ↑Wed Aug 10, 2022 3:11 pm Maybe Nu...

Organonfire
Wed Aug 10, 2022 3:41 pm

x

Re: Question about Automation Clips

nucleon wrote: ↑Wed Aug 10, 2022 3:25 pm abelg ...

Organonfire
Wed Aug 10, 2022 3:45 pm

x

Re: Question about Automation Clips

abelg wrote: ↑Wed Aug 10, 2022 3:11 pm Maybe Nu...

Organonfire
Wed Aug 10, 2022 3:48 pm

x

Re: Question about Automation Clips

levendis wrote: ↑Wed Aug 10, 2022 3:12 pm Autom...

Organonfire
Wed Aug 10, 2022 3:59 pm

x

Re: Question about Automation Clips

Sancho Slikk wrote: ↑Wed Aug 10, 2022 3:23 pm D...

Organonfire
Thu Aug 11, 2022 1:35 am

x

Re: Question about Automation Clips

nucleon wrote: ↑Wed Aug 10, 2022 3:25 pm abelg ...

Organonfire
Thu Aug 11, 2022 1:37 am

x

Re: Question about Automation Clips

abelg wrote: ↑Wed Aug 10, 2022 3:11 pm Maybe Nu...

nucleon
Thu Aug 11, 2022 8:03 am

x

Re: Question about Automation Clips

Organonfire wrote: ↑Thu Aug 11, 2022 1:35 am nu...


Return to “FL Studio Users Forum (Looptalk)”